Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
2960-24TT starting…
Base ethernet MAC Address: 0002.175C.B6D5
Xmodem file system is available.
Initializing Flash…
flashfs[0]: 1 files, 0 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 64016384
flashfs[0]: Bytes used: 4414921
flashfs[0]: Bytes available: 59601463
flashfs[0]: flashfs fsck took 1 seconds.
…done Initializing Flash.
Boot Sector Filesystem (bs:) installed, fsid: 3
Parameter Block Filesystem (pb:) installed, fsid: 4
Loading “flash:/c2960-lanbase-mz.122-25.FX.bin”…
######################################### [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software – Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 12-Oct-05 22:05 by pt_team
Image text-base: 0×80008098, data-base: 0×814129C4
Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
24 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)
64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 0002.175C.B6D5
Motherboard assembly number : 73-9832-06
Power supply part number : 341-0097-02
Motherboard serial number : FOC103248MJ
Power supply serial number : DCA102133JA
Model revision number : B0
Motherboard revision number : C0
Model number : WS-C2960-24TT
System serial number : FOC1033Z1EY
Top Assembly Part Number : 800-26671-02
Top Assembly Revision Number : B0
Version ID : V02
CLEI Code Number : COM3K00BRA
Hardware Board Revision Number : 0×01
Switch Ports Model SW Version SW Image
—— —– —– ———- ———-
* 1 26 WS-C2960-24TT 12.2 C2960-LANBASE-M
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 12-Oct-05 22:05 by pt_team
Press RETURN to get started!
Switch>ena
Switch#s
Switch#se
Switch#setup
Switch#setup
Switch#setup ?
Switch#setup
— System Configuration Dialog —
Continue with configuration dialog? [yes/no]: yes
At any point you may enter a question mark ‘?’ for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets ‘[]‘.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]: yes
Configuring global parameters:
Enter host name [Switch]: helmstandart
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: rhino
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: rhino
% Please choose a password that is different from the enable secret
Enter enable password: cakep
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: cakep
Configure SNMP Network Management? [yes]:
% This version of Packet Tracer does not support SNMP management setup.
Configure SNMP Network Management? [yes]:yes
% This version of Packet Tracer does not support SNMP management setup.
Configure SNMP Network Management? [yes]:no
Configuring interface parameters:
Do you want to configure Vlan1 interface? [yes]:yes
Configure IP on this interface? [yes]: yes
IP address for this interface: 192.168.0.101
Subnet mask for this interface [255.255.255.0] : 255.255.255.0
Would you like to enable as a cluster command switch? [yes/no]:no
The following configuration command script was created:
!
hostname helmstandart
enable secret 5 $1$mERr$oU7khLPiPJy4.lkjTjSAT/
enable password cakep
line vty 0 4
password cakep
!
interface Vlan1
ip address 192.168.0.101 255.255.255.0
!
interface FastEthernet0/1
no ip address
!
interface FastEthernet0/2
no ip address
!
interface FastEthernet0/3
no ip address
!
interface FastEthernet0/4
no ip address
!
interface FastEthernet0/5
no ip address
!
interface FastEthernet0/6
no ip address
!
interface FastEthernet0/7
no ip address
!
interface FastEthernet0/8
no ip address
!
interface FastEthernet0/9
no ip address
!
interface FastEthernet0/10
no ip address
!
interface FastEthernet0/11
no ip address
!
interface FastEthernet0/12
no ip address
!
interface FastEthernet0/13
no ip address
!
interface FastEthernet0/14
no ip address
!
interface FastEthernet0/15
no ip address
!
interface FastEthernet0/16
no ip address
!
interface FastEthernet0/17
no ip address
!
interface FastEthernet0/18
no ip address
!
interface FastEthernet0/19
no ip address
!
interface FastEthernet0/20
no ip address
!
interface FastEthernet0/21
no ip address
!
interface FastEthernet0/22
no ip address
!
interface FastEthernet0/23
no ip address
!
interface FastEthernet0/24
no ip address
!
interface GigabitEthernet1/1
no ip address
!
interface GigabitEthernet1/2
no ip address
!
end
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]: 2
Building configuration…
[OK]
Use the enabled mode ‘configure’ command to modify this configuration.
helmstandart#
0 komentar:
Posting Komentar